Miller Big Blue 400 CX CE Manuel du propriétaire Page 55
- Page / 82
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
OM-4435 Page 49
B. Standard Generator Power
Trouble Remedy
No generator power output at AC recep-
tacles; weld output okay.
Reset receptacle supplementary protectors (see Section 7-1).
No generator power or weld output. Disconnect equipment from generator power receptacles during start-up.
Check fuse F1, and replace if open (see Section 8-10). Have Factory Authorized Service Agent check
field excitation circuit.
Reset supplementary protector CB3 (see Section 8-10).
Check Voltmeter/Ammeter help displays (see Section 8-11).
Have Factory Authorized Service Agent check brushes and slip rings, and field excitation circuit.
High output at generator power AC re-
ceptacles.
Have Factory Authorized Service Agent check field excitation circuit.
Low output at generator power AC re-
ceptacles.
Check engine speed, and adjust if necessary.
Check fuse F1, and replace if open (see Section 8-10). If F1 is open, have Factory Authorized Service
Agent check the rotor.
C. Engine
Trouble Remedy
Engine will not crank. Check battery, and replace if necessary.
Check battery connections and tighten if necessary.
Circuit breaker CB1 may be open. CB1 automatically resets when fault is corrected (see Section 8-10).
Have Factory Authorized Service Agent check engine wiring harness and components.
Reset supplementary protector CB2 (see Section 8-10).
Check engine wiring harness plug connections.
Have Factory Authorized Service Agent check Engine Control switch S1, Fuel/Hour gauge FUEL/HM,
and control relay CR2.
Engine cranks but does not start. Check fuel level.
Check battery and replace if necessary. Check engine charging system according to engine manual.
Have Factory Authorized Service Agent check control relay CR1, Fuel/Hour gauge FUEL/HM, fuel
solenoid FS1, and the fuel pump.
Air in fuel system. See engine manual.
Engine hard to start in cold weather. Use Preheat switch S4 (see Section 6-2).
Keep battery in good condition. Store battery in warm area off cold surface.
Use fuel formulated for cold weather (diesel fuel can gel in cold weather). Contact local fuel supplier for
fuel information.
Use correct grade oil for cold weather (see Section 8-1).
Have Factory Authorized Service Agent check Preheat switch S4, control relay CR3, and the glow
plug.
Engine suddenly stops. Check oil and coolant levels. Automatic shutdown system stops engine if oil pressure is too low or coolant
temperature is too high (see Section 5-8 ).
Check fuel/hour meter for indication of shutdown.
Reset supplementary protector CB2 and/or clear fault causing circuit breaker CB1 to trip (see Section
8-10). Have Factory Authorized Service Agent check engine alternator, engine harness, fuel solenoid
FS1, and the fuel pump.
Have Factory Authorized Service Agent check Engine Control switch S1, control relay CR1, inte-
grated rectifier SR2, fuel solenoid FS1, and the fuel pump.
See engine manual.
- Big Blue 400 CX CE 1
- From Miller to You 2
- TABLE OF CONTENTS 3
- DECLARATION OF CONFORMITY 5
- 1-1. Symbol Usage 7
- 1-2. Arc Welding Hazards 7
- 1-3. Engine Hazards 9
- 1-4. Hydraulic Hazards 10
- 1-5. Compressed Air Hazards 10
- HOSES can injure 11
- HOT PARTS can burn 11
- WELDING WIRE can injure 12
- READ INSTRUCTIONS 12
- 1-9. EMF Information 13
- UTILISATION 14
- Les ÉQUIPEMENTS HYDRAULIQUES 17
- LIRE LES INSTRUCTIONS 20
- SECTION 3 − DEFINITIONS 22
- 3-2. Symbols And Definitions 23
- SECTION 4 − SPECIFICATIONS 24
- 4-4. Volt-Ampere Curves 25
- 4-7. AC Generator Power Curve 27
- SECTION 5 − INSTALLATION 28
- ! Do not weld on base. Weld 29
- Electrically bond generator 30
- Work like a Pro! 31
- ° F (−37° C). Add anti 33
- ° F (−37° C) 33
- ! Stop engine 34
- ! Stop engine before 35
- ! Do not use worn 35
- OM-4435 Page 31 37
- 287 125−A / 804 009−F 38
- 6-3. Process/Contactor Switch 40
- Arc Start With Lift-Arc 41
- Arc End With Crater-Out 41
- Arc End With Auto-Stop 41
- OM-4435 Page 37 43
- Ref. 287 125-A 44
- 8-1. Maintenance Label 45
- 8-2. Routine Maintenance 46
- ! Stop engine and let cool 47
- 8-5. Servicing Air Cleaner 48
- 8-10. Overload Protection 52
- Ref. 804 009-F 53
- 8-12. Troubleshooting 54
- B. Standard Generator Power 55
- C. Engine 55
- Trouble Remedy 56
- OM-4435 Page 51 57
- OM-4435 Page 52 58
- OM-4435 Page 53 59
- SECTION 10 − RUN-IN PROCEDURE 60
- ! Do not touch hot exhaust 61
- ! Keep exhaust and pipe away 61
- 11-1. Selecting Equipment 63
- ! Ground generator to system 64
- ! Also see AWS Safety & 64
- Ref. ST-800 396-A / S-0625 67
- Customer-supplied equipment 68
- SECTION 12 − PARTS LIST 70
- 804 012−J1 / 804 012-H2 71
- OM-4435 Page 66 72
- OM-4435 Page 67 73
- OM-4435 Page 68 74
- Hardware is common and not 75
- OM-4435 Page 70 76
- OM-4435 Page 74 80
- Effective January 1, 2011 81
- For Service 82
- Owner’s Record 82
Produits connexes et manuels pour Système de soudage Miller Big Blue 400 CX CE
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.015 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels